Metal Push Button Switch 12mm IP65 Self-Locking Stainless Steel Push Button Switch

JCPT push button swap 12mm IP65 self-locking stainless metal push button change
 

Product Description
 
 
LA128 Mounting Diameter Method of connection Head condition Switch combination Head kind Luminescence sort Luminous coloration Lamp voltage Shell content
JCPT φ8
φ10
φ12
φ16
φ19
φ22
φ25
φ28
φ30
φ35
φ40
A pin sort
B terminal
C Ultra quick variety
P Flat round bevel shell
G High head round slant shell
1NO-ten
NO is usually open up speak to
1NC-01 is normally shut get in touch with
Momentary
D:with light-weight
DZ: with lamp lock
Z: self locking
D Solitary point
E Annular
DY Energy supply
R
G
B
Y
W
O
P
five
six
12
24
36
48
a hundred and ten
220
380
AC220
AC380
S Stainless steel
N Brass plating
P Plastic

 

Undertaking Parameter Undertaking Parameter
Swap sort Quickly relocating single make contact with Explosion quality IK10 for steel material
Speak to resistance ≤50mΩ Working pressure two.five-4.5N
Insulation strength ≥1000MΩ Operation timetable Related to about 2mm,head office about 3mm
Ambient temperature -20ºC~+55ºC Nut Torque five-14N,m
Electrical lifestyle ≥50000 times Outer shell Stainless metal/Nickel plating on brass/Aluminum alloy oxidatio/Plastic
Mechanical life ≥500000 occasions Push crucial Stainless steel/Nickel plating on brass/Aluminum alloy oxidatio/Plastic
Water-resistant grade IP67 Base seat JCPT
    Contact position Silver alloy

Operate of drive button change
Reset – push the energy to release the energy OFF- (0N)
Self latching – click on electricity and then push the electricity 0FF-0N

Software:
Audio / Video solution: MP3, MP4, DVD, stereo method
Digital gadgets: electronic digicam, electronic video
Remote management: Automobile, rolling door, Residence safety items
JCPT merchandise: mobiles, automobile telephone, telephone, constructing equipment, PDA and so on.
House Appliances: Television, microwave oven, electric cooker, electric powered hair drier, electronic scale, Body Unwanted fat &H2o Scale, Kitchen Scale.
Stability Merchandise: Videophone, Monitor and so forth.
Toy: digital toy etc.
Computer merchandise: Camera, recording pen and many others.
Fitness gear: running device, therapeutic massage chair, timer etc.
JCPT Equipment: sphygmomanometer, thermometer, the clinic call system and other comparable merchandise.

Soldering
1. Standard Safety measures
Before soldering the Switch on a multilayer PCB, test to affirm that soldering can be performed appropriately. Normally the Swap might be deformed by the soldering warmth on the sample or lands of the multilayer PCB. 
Do not solder the Swap a lot more than 2 times, like rectification soldering. An interval of five minutes is necessary amongst the 1st and 2nd soldering.

2. JCPTmatic Soldering Baths 
Soldering temperature: 260°C max.
Soldering time: 5 s max. for a 1.6-mm thick one-aspect PCB
Preheating temperature: 100°C max. (ambient temperature)
Preheating time: Inside of sixty s
Make positive that no flux will rise previously mentioned the stage of the PCB. If fluxoverflows onto the mounting surface area of the PCB, it may possibly enter the Switch and cause a malfunction. 

3. Reflow Soldering (Surface Mounting)
Solder the terminals inside of the heating curve shown in the following diagram.
Note: The previously mentioned heating curve applies if the PCB thickness is one.six mm.
The peak temperature may vary based on the reflow bathtub utilised. Validate the conditions beforehand.
Do not use an automatic soldering bath for area-mounted Switches. The soldering gasoline or flux may enter the Swap and damage the Switch’s thrust-button procedure. 

4. Handbook Soldering (All Models)
Soldering temperature: 350°C max. at the tip of the soldering iron
Soldering time: three s max. for a 1.6-mm thick, single-aspect PCB
Just before soldering the Change on a PCB, make positive that there is no unneeded place among the Switch and the PCB.

Metal Push Button Switch 12mm IP65 Self-Locking Stainless Steel Push Button Switch